產品型號：TM-L03W-E
應用范圍：照明、指示、背光等
產品描述：台銘直插式LED,體積小,高亮度,能耗低,應用於照明,背光等領域。
產品介紹注：亮度、角度、色溫、紫光波段均可按客戶要求做貨。
| Type 規格/型號 | Emitting Color 顏色 | Material 原材料 | View Angle 發光角度 | VF(V) 電壓 | IV (MCD) 亮度 | WL(nm) 波長 | IF(MA） 電流 | |||
| Typ | Max | Min | Typ | Min | Max | |||||
| TM-L03R-E （紅光） | Red | AlGaInP | 30° | 1.8 | 2.4 | 2000 | 4000 | 620 | 630 | 20MA |
| TM-L03Y-E （黃光） | Yellow | AlGaInP | 30° | 1.8 | 2.4 | 300 | 600 | 585 | 595 | 20MA |
| TM-L03O-E （黃綠） | Yellow Green | AlGaInP | 30° | 1.8 | 2.4 | 50 | 100 | 565 | 575 | 20MA |
| TM-L03O-E （橙光） | orange | AlGaInP | 30° | 1.8 | 2.4 | 300 | 600 | 600 | 610 | 20MA |
| TM-L3CG-E （翠綠） | Green | InGaN/GaN | 30° | 2.8 | 3.4 | 1200 | 8000 | 520 | 530 | 20MA |
| TM-L3B-E （藍光） | Blue | InGaN/GaN | 30° | 2.8 | 3.4 | 300 | 500 | 460 | 475 | 20MA |
| TM-L3UV365-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 6 | 8 | 365 | 370 | 20MA |
| TM-L03UV370-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 10 | 13 | 370 | 375 | 20MA |
| TM-L3UV380-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 14 | 18 | 380 | 385 | 20MA |
| TM-L03UV400-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 60 | 70 | 395 | 400 | 20MA |
| TM-L03UV405-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 70 | 80 | 400 | 405 | 20MA |
| TM-L03UV410-E （紫光） | Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 80 | 90 | 405 | 410 | 20MA |
| TM-L3NB55-E （白光） | White | InGaN/GaN | 30° | 2.8 | --- | 6000 | --- | 5500 | 6000 | 20MA |
| TM-L3ZB65-E （白光） | White | InGaN/GaN | 45° | 2.8 | --- | 6000 | --- | 6500 | 7000 | 20MA |
| TM-L3LB80-E （白光） | White | InGaN/GaN | 30° | 2.8 | --- | 6000 | --- | 2500 | 10000 | 20MA |
Supporter shaping：
Shaping of the supporter must be conductedbefore welding. While shaping, the
bending position of the supporter must at least be located at3mm from the bottom
of the encapsulating resin. Also, avoid multiple bending onthe same position。 Please
choose the
appropriate apparatus to fixate the supporter in order toavoid exerting extra pressure
on resin. Using the jointing section of the pin and resin asfulcrum is strictly
prohibited since the pressure mounted would directly damagethe internal 。
illuminating structure and thus cause irreversible defectionof the product..Due to the
same reason, the interval between the welding hole on the PCBboard should be
strictly matched with the pin interval of the product whenassembling theproduct.
